Deep dive

water-based coatings: what the words hide.

Aqueous, dispersion and water-based cup coatings are plastic polymers applied from water. The chemistry (acrylic, styrene-acrylic, polyolefin), the recycling case for them, the compostability case against them, and how plastic-free claims survive on a plastic film.

Updated November 11, 2026 · By Made to Disappear

in short.

  • A dispersion coating is polymer particles in water that fuse into a plastic film as the water dries. Manufacturers list the polymers: acrylic latex, styrene-acrylic latex, polyolefin dispersions.
  • Their genuine advantage is recyclability: the thin film separates in a paper mill's pulper, and mills report over 90% fibre recovery.
  • Their weakness is the opposite claim. The dried film is a synthetic plastic, EU guidance treats a coated paper cup as partly plastic, and a compost certificate can be earned while the coating itself goes untested as a minor constituent.

the chemistry.

A barrier coating has to stop water and grease getting into paper. The traditional answer is a laminated polyethylene film about 15 to 20 microns thick. A dispersion coating replaces the film with a liquid: polymer particles a fraction of a micron across, suspended in water with stabilisers and often wax or mineral fillers. It is metered onto the board on the paper machine or a coater, the water is driven off in dryers, and the particles coalesce into a continuous film a few microns thick.

What the particles are made of is public information. Dow's barrier range for cup stock and quick-serve packaging lists an acrylic copolymer latex, a styrene-acrylic latex and acid-modified polyolefin dispersions. BASF and others sell equivalent styrene-acrylic dispersions pitched as replacements for wax and PE. The European coatings trade body describes the category to regulators as polyethylene water-based suspensions and acrylic resin-based suspensions. Acrylic, styrene-acrylic and polyolefin are petrochemical plastics. The water is the solvent, not the product.

the honest case for them: recycling.

There is a real reason mills and brands like dispersion coatings, and it is not compostability. A thin coalesced film breaks up in a repulper far more easily than a laminated PE sheet, so coated cups can go through a standard paper mill with high fibre yield. Dow cites fibre recovery of 91% and over 99% in recycling trials for two of its cup-stock dispersions. If your cups are collected for paper recycling and your mill accepts them, a dispersion-coated cup is a better recycling feedstock than a PE-lined one.

That is a recycling claim. It is not a composting claim, and it says nothing about what the film does in soil.

plastic-free, by the rules.

The European Commission's guidelines on the Single-Use Plastics Directive treat a paper or board product with a plastic coating or lining applied against water or grease as a composite that is partly made of plastic, inside the Directive. The cups table in the guidelines lists empty paper-based cups with plastic lining or coating as covered. Germany's implementing FAQ, asked whether water-based or aqueous dispersions are exempt, answers that there is no general exception and it depends on the nature of the coating. The coatings industry has lodged a formal statement asking for a carve-out on the grounds that an acrylic coating is not structural; even that statement calls the coatings acrylic and PE suspensions.

In Canada there is no cup-specific rule, but the Competition Bureau's 2025 guidelines on environmental claims apply to any claim a business makes: it must rest on adequate and proper testing done before the claim is made, a literally true statement can still create a misleading general impression, and a disclaimer does not cure it. Plastic-free on a cup with an acrylic film is the kind of claim those guidelines were written for, and since June 2025 competitors and the public can bring their own cases.

compostable, by the threshold.

Some water-based cups carry compost logos, including home compost logos. Three routes lead there. The first is legitimate: the coating polymer is itself a compostable material (there are dispersion-coating grades built on PHA and on other certified polymers) and the finished cup was tested. The second is the material-versus-product gap: the base board was certified, the coated cup was not, and the logo moved from one to the other. The third is the threshold.

Under the EN 13432 family of standards, constituents present at less than 1% of an item's mass do not have to demonstrate biodegradation, as long as the untested total stays under 5%. A coating at a few grams per square metre on cup board weighing a few hundred can sit under 1%. Whether a certifier will let a non-compostable acrylic film through on that basis is the certifier's call: TÜV Austria says in writing that it does not accept any intentional addition of structural polymers deemed unable to biodegrade at any concentration, but the standards themselves permit it and not every scheme closes the door.

A film that was never tested, made of a polymer that does not pass the test on its own, does not disappear because the paper around it did. It breaks into flakes in the pile and leaves with the compost. That is where the plastic-free water-based cup and the microplastic in the garden bed meet.

how to read a water-based cup.

  1. 1

    Ask for the polymer by name. Acrylic, styrene-acrylic, polyolefin: plastic film, recyclable where accepted, not compostable unless proven. PHA or another certified polymer: possibly compostable; ask for the next two things.

  2. 2

    Ask whether the coating was tested or excused. The certificate scope will say whether the finished cup was tested and which constituents were exempt.

  3. 3

    Match the claim to the stream your cups actually enter. A recyclable cup in a city with no cup recycling is waste. A home compostable cup composts wherever the customer takes it.

Our answer: paper with a PHA lining, 100% certified home-compostable material, certified by TÜV Austria. See the comparison with PHA for the side-by-side.

questions.

What is a water-based cup coating made of?

Most are acrylic, styrene-acrylic or polyolefin polymer particles dispersed in water, which dry into a continuous plastic film on the paper. Manufacturers list these chemistries on their product pages.

Is a water-based coating plastic?

The dried film is a synthetic polymer. The European Commission's guidelines treat paper cups with a plastic coating as partly made of plastic, and German guidance gives no general exemption to aqueous dispersions.

Are water-based cups recyclable?

Often, yes, where cups are collected for paper recycling. The thin film separates in the pulper and mills report high fibre recovery. That is the coating's real advantage.

Are water-based cups home compostable?

Only if the coating polymer itself was tested and passed. Compost standards allow constituents under 1% of the item to go untested, so a logo on the cup does not by itself prove the coating breaks down.

Why do water-based cups say plastic-free?

Because the coating is applied from water rather than laminated as a sheet, and because the film is thin. Neither changes the polymer. Canadian competition law requires environmental claims to be tested and not misleading in their general impression.

sources.

  1. Dow, Barrier coatings for fibre-based foodservice packaging: product page listing acrylic latex, styrene-acrylic latex and polyolefin dispersion coatings for cup stock. www.dow.com/en-us/market/mkt-pulp-paper/sub-paper-barrier-coating/app-paper-barrier-quick-serve.html
  2. EuPIA (European Printing Ink Association), Statement on the applicability of the Single-Use Plastics Directive to functional coatings, November 2025. www.eupia.org/wp-content/uploads/2025/11/202511_Statement-on-functional-coatings-and-Single-Use-Plastics-Directive_Final.pdf
  3. European Commission, Commission guidelines on single-use plastic products in accordance with Directive (EU) 2019/904, Official Journal C 216, 7 June 2021. eur-lex.europa.eu/legal-content/EN/TXT/?uri=CELEX:52021XC0607(03)
  4. TÜV Austria Belgium, Certification scheme Seedling (based on EN 13432), 2024, section on constituents and additives. be.tuvaustria.com/wp-content/uploads/sites/73/2024/03/CS-Seedling_EN.pdf
  5. TÜV Austria, Comparison of compostability standards (EN 13432, ISO 17088, ASTM D6400, AS 4736, ISO 18606), 2024. okcert.tuvaustria.com/wp-content/uploads/sites/76/2024/12/PD-BA-TABE-CERT-BIO-ID-415_comparison_standards_EN_2407.pdf
  6. Competition Bureau Canada, Environmental claims and the Competition Act, enforcement guidelines, June 2025. competition-bureau.canada.ca/en/how-we-foster-competition/education-and-outreach/publications/environmental-claims-and-competition-act

We cite standards, regulators, certifiers, peer-reviewed journals and manufacturers’ own technical pages. If you think we have something wrong, write to hello@madetodisappear.com and we will check it.

Everything we sell is made from 100% certified home-compostable material, certified by TÜV Austria. see the certificates.

keep reading.